Refrigerator Repair Columbus

The refrigerator door gasket is the rubber seal that goes around the outer edge of the refrigerator door. The purpose of the refrigerator gasket is to create an airtight seal so when you shut your fridge door, everything stays cold inside, and the temperature remains consistent.

The gasket can get dirty over time, as crumbs drop into the folds and liquids spill in the fridge. To keep the gasket clean, wipe it down with a wet soapy cloth. Be sure to clean in between the crevices of the gasket.

Keep an eye on the quality of the gasket as well. If the gasket ever develops cracks or rips or is covered in mold, it needs to be replaced. You can replace a gasket on your own, or you can call in a professional for assistance. The gasket has to be installed correctly to keep your fridge at the right temperature, so take care with the installation process.

You can purchase a replacement gasket at your local hardware or appliance store. To purchase the right gasket, you need the make and model of your fridge. If you replace the gasket on your own, follow these instructions. Take your new gasket and soak it in some warm water; this helps make the material more flexible and easier to work with. While the new gasket is soaking, remove the old gasket.

For removal, open the refrigerator door all the way. Screws, which are hidden behind the first flap of the gasket, hold most gaskets in place. Pull the first flap of the gasket back and remove the screws all around the edge of the fridge. Alternatively, some gaskets are held in place with clips, which you will need to loosen before removing the gasket. After you do remove the screws or clips that hold the gasket in place, start at the top and pull the gasket off. Clean the area where the gasket was on your fridge.

Get the new gasket out of the sink, dry it off, and start placing it in the upper corner, working your way around the fridge, sliding it into place. Once the gasket is in place, tighten the clips or screws.

The condenser coils keep your fridge cool. They should be cleaned at least once a year.

The condenser coils on most residential refrigerators are located at the front base behind the base grill or on the backside of your fridge. On a few rare residential models, the condenser coils are located on the top of the fridge.

Before cleaning the condenser coils, you should unplug your refrigerator. Then, you need to gain access to the coils. To do this, remove the base grille or pull the fridge away from the wall.

Then, clean the coils with a coil brush in order to remove all the built-up dirt and dust on the coils. Follow up by gently vacuuming the coils. You may want to use the crevice tool and the brush tool on your vacuum for this job. Once you have vacuumed, put your fridge back together, and plug the refrigerator back in.

This is a task you can take care of yourself, or you can have an appliance repair person perform this task for you.

Because the food inside your freezer doesn’t rot, you don’t need to scour the freezer as often as you do your fridge’s vegetable and fruit boxes. However, stale food smells can start to seep into your freezer over time, and accidental spills can freeze and harden along the freezer’s shelves.

At least twice a year, remove all the food from your freezer (you can remove and replace the food one shelf at a time to prevent melting or else store the food in a cooler while you clean). Using a warm rag dipped in a combination of water and dish soap, carefully rinse and dry every shelf in your freezer. Don’t forget to clean the sides of the freezer and the rubber seal that keeps the freezer’s icy air in.

For harder-to-remove stains, scour the shelves or walls more thoroughly with baking soda, which removes bad smells more effectively than dish soap.

Once you’ve finished rinsing a shelf, make sure to dry it off thoroughly with a clean rag. Don’t forget to clean the outside of the freezer, too, removing any unsightly food stains or condensation that could cause rust.

Many modern freezers defrost automatically, but older ones might need you to defrost them manually once the ice is too thick by unplugging the unit and leaving the freezer door open until the ice melts.

Before you start defrosting your freezer, cover the floor with thick towels. Make sure the freezer’s plug and the electrical socket are well out of the way of any water that could drip onto the floor. Change the towels periodically when they’re wet, and keep family members out of the kitchen until the area is no longer a slip hazard.

Once the freezer is done defrosting and you’ve plugged it back in, don’t replace your food immediately. Instead, wait for the freezer to cool to the proper temperature before you put your food back. Otherwise, your food could spoil and then refreeze, leaving you vulnerable to food poisoning and freezer messes.